MРЗС-05Л AИAР.466452.001-32

It performs the following functions:

Provides control and measurement of the following values:

• phase currents Ia, Ic, Ib - from 0,1 to 30 Iн (Iн = 5 А);
• current of one phase of 0.4 kV connection - from 0.5 to 150 A);
• zero sequence current - from 0.01 to 2 A;
• three phase or line voltages - up to 150 V;
• zero phase-sequence voltage - up to 150V;
• line voltage of the standby line - up to 150 V (only in -12 and -32);
• angles between all analog measurements of the main line;
• network frequencies;
• active power with a sign;
• reactive power with a sign;
• full power;
• power factor;
• interphase active and reactive resistances.

Relay protection functions:

• four-stage overcurrent protection (OCP), has the following stages:
• 1 - stage with definite time delay (current pinch-off), or with the possibility of a voltage triggering, or directional OCP with an independent time delay;
• 2 - stage with definite time delay with the possibility of voltage triggering or with a time-dependent delay (in accordance with IES 255-4 types A, B, C, RТ-80, RТV-1 characteristics), or directional OCP with an independent time delay;
• 3 - stage with a definite time delay (overload protection) with the possibility of voltage triggering or directional OCP;
• 4 - directi stage with a definite time delay (overload protection) with the possibility of voltage triggering or onal OCP.
• Directional ground fault protection (DGFP) - with the choice of the direction of action and the possibility of switching to non-directional (with respect to the current 3Io or voltage 3Uo) or to a non-directional by the sum of the higher harmonics 3Io.
• two-stage undervoltage protection with the ability to control the current and the inclusion of triggers for AND or OR.
• two-stage overvoltage protection with the inclusion of triggers for AND or OR.
• negative phase-sequence protection (NPSP), reacts to the ratio of the negative sequence current to the direct sequence current (phase failure monitoring (PFM));
• arc fault protection (AFP): start of AFP is carried out through a discrete input from an external arc protection sensor with the ability of current control;
• circuit-breaker failure protection (CBFP) with current control: CBFP is initiated when cut-off tripping events or via a binary input. CBFP has two stages in response time.
• implementation of busbar protection scheme (BPS).

Automation functions:

• four-time recloser (AR). The AR is started from OCP. Provides the ability to block reclosing through a discrete input;
• automatic frequency load shedding (UFLS with FAR) (in -12 and -32 - from two inputs);
• automatic transfer switch (ATS);
• multiple automatic reclosing when disconnected from the undervoltage protection;
• circuit breaker control. The circuit breaker can be switched on and off both from the device and via a discrete input (pulsed). If there is a command to cut off the circuit breaker, the on signal is blocked;
• acceleration of OCP after the switch is turned on, or if the second stage of the OCP is forced into the accelerated mode.
• voltage control of both sections (only in -12 and -32);
• circuit breaker closing and opening monitoring;
• control of commutation life of switch.

Defined functions, triggers and logical elements:

• number of defined functions - 8;
• number of defined triggers - 4, The status of triggers is stored in non-volatile memory;

Emergency registrar of oscillograms of currents with recording of discrete signals:

• parameterizable duration of pre-emergency and emergency recording.
• resolution of the recorder by analog signals - not more than 1.25 ms.
• total recording time - 66 s.

Discrete event recorder:

• 48 recent events,
• up to 43 entries in each accident with a discreteness in time - 1 ms,
• for each accident the following are recorded:
  • all discrete signals with fixation of arrival and departure time;
  • maximum values of phase current with the fixation of remaining currents and voltages;
  • maximum value of the current 3Io with the fixation of the remaining currents and voltages;
  • maximum value of the voltage 3Uo with the fixation of the remaining currents and voltages;
  • maximum value of the ratio of the current of the negative sequence to the current of the direct sequence with the fixation of the remaining currents and voltages;
  • maximum value of phase or line voltages with fixation of remaining currents and voltages;
  • minimum value of phase or linear voltages with fixation of remaining currents and voltages;
  • minimum value of frequency Р1 with fixation of remaining currents and voltages;
  • minimum value of frequency P2 with fixation of remaining currents and voltages;
  • value of frequency Р1 with fixation of remaining currents and voltages at the moment of FAR operation;
  • value of frequency Р2 with fixation of remaining currents and voltages at the moment of FAR operation.

Energy metering:

• active energy - in two directions;
• reactive energy - in four quadrants

Determining the fault location.

Four groups of settings for all protections.

Short-circuit currents auxiliary power supply If the power supply of the device at the power input of 220 V (or 110 V) The device can be powered from current transformers of phases A and C. In this case, the magnitude of the current must be 4 A or more for one of the phases or for the total of two phases.

Binary inputs feeding from internal source - from the DIP output, two discrete inputs can be energized

Number of freely programmable inputs, outputs, indicators:

• discrete inputs - 10, with the possibility of autonomous power supply of a discrete input;
• discrete relay outputs - 10, without and with the memorization, realization of ShMS;
• LED indicators - 8, with and without memory.
• All inputs, outputs, indicators are freely programmable.
• Multilingual menu - 3 languages supported.
• Provides input-output from the work of all protections or their individual stages.
• Six freely programmable buttons.
• Work with an external computer is carried out through the USB port.
• For the device to work in the local network interface RS-485 is provided.
• Communication protocol - ModBus RTU. In MRZS-05L (-12) (-32) optional – IEC 06870-5-104.